CVE Database

In the Linux kernel, the following vulnerability has been resolved: iio: imu: st_lsm6dsx: Set buffer sampling frequency for accelerometer only The st_lsm6dsx_hwfifo_odr_store() function, which is called when userspace writes the buffer sampling frequency sysfs attribute, calls st_lsm6dsx_check_odr(), which accesses the odr_table array at index `sensor->id`; since this array is only 2 entries long, an access for any sensor type other than accelerometer or gyroscope is an out-of-bounds access. The motivation for being able to set a buffer frequency different from the sensor sampling frequency is to support use cases that need accurate event detection (which requires a high sampling frequency) while retrieving sensor data at low frequency. Since all the supported event types are generated from acceleration data only, do not create the buffer sampling frequency attribute for sensor types other than the accelerometer.

In the Linux kernel, the following vulnerability has been resolved: iio: gyro: mpu3050: Move iio_device_register() to correct location iio_device_register() should be at the end of the probe function to prevent race conditions. Place iio_device_register() at the end of the probe function and place iio_device_unregister() accordingly.

In the Linux kernel, the following vulnerability has been resolved: usb: ulpi: fix double free in ulpi_register_interface() error path When device_register() fails, ulpi_register() calls put_device() on ulpi->dev. The device release callback ulpi_dev_release() drops the OF node reference and frees ulpi, but the current error path in ulpi_register_interface() then calls kfree(ulpi) again, causing a double free. Let put_device() handle the cleanup through ulpi_dev_release() and avoid freeing ulpi again in ulpi_register_interface().

In the Linux kernel, the following vulnerability has been resolved: usb: usbtmc: Flush anchored URBs in usbtmc_release When calling usbtmc_release, pending anchored URBs must be flushed or killed to prevent use-after-free errors (e.g. in the HCD giveback path). Call usbtmc_draw_down() to allow anchored URBs to be completed.

In the Linux kernel, the following vulnerability has been resolved: comedi: me_daq: Fix potential overrun of firmware buffer `me2600_xilinx_download()` loads the firmware that was requested by `request_firmware()`. It is possible for it to overrun the source buffer because it blindly trusts the file format. It reads a data stream length from the first 4 bytes into variable `file_length` and reads the data stream contents of length `file_length` from offset 16 onwards. Although it checks that the supplied firmware is at least 16 bytes long, it does not check that it is long enough to contain the data stream. Add a test to ensure that the supplied firmware is long enough to contain the header and the data stream. On failure, log an error and return `-EINVAL`.

In the Linux kernel, the following vulnerability has been resolved: comedi: me4000: Fix potential overrun of firmware buffer `me4000_xilinx_download()` loads the firmware that was requested by `request_firmware()`. It is possible for it to overrun the source buffer because it blindly trusts the file format. It reads a data stream length from the first 4 bytes into variable `file_length` and reads the data stream contents of length `file_length` from offset 16 onwards. Add a test to ensure that the supplied firmware is long enough to contain the header and the data stream. On failure, log an error and return `-EINVAL`. Note: The firmware loading was totally broken before commit ac584af59945 ("staging: comedi: me4000: fix firmware downloading"), but that is the most sensible target for this fix.

In the Linux kernel, the following vulnerability has been resolved: reset: gpio: fix double free in reset_add_gpio_aux_device() error path When __auxiliary_device_add() fails, reset_add_gpio_aux_device() calls auxiliary_device_uninit(adev). The device release callback reset_gpio_aux_device_release() frees adev, but the current error path then calls kfree(adev) again, causing a double free. Keep kfree(adev) for the auxiliary_device_init() failure path, but avoid freeing adev after auxiliary_device_uninit().

In the Linux kernel, the following vulnerability has been resolved: nvmem: zynqmp_nvmem: Fix buffer size in DMA and memcpy Buffer size used in dma allocation and memcpy is wrong. It can lead to undersized DMA buffer access and possible memory corruption. use correct buffer size in dma_alloc_coherent and memcpy.

In the Linux kernel, the following vulnerability has been resolved: vt: discard stale unicode buffer on alt screen exit after resize When enter_alt_screen() saves vc_uni_lines into vc_saved_uni_lines and sets vc_uni_lines to NULL, a subsequent console resize via vc_do_resize() skips reallocating the unicode buffer because vc_uni_lines is NULL. However, vc_saved_uni_lines still points to the old buffer allocated for the original dimensions. When leave_alt_screen() later restores vc_saved_uni_lines, the buffer dimensions no longer match vc_rows/vc_cols. Any operation that iterates over the unicode buffer using the current dimensions (e.g. csi_J clearing the screen) will access memory out of bounds, causing a kernel oops: BUG: unable to handle page fault for address: 0x0000002000000020 RIP: 0010:csi_J+0x133/0x2d0 The faulting address 0x0000002000000020 is two adjacent u32 space characters (0x20) interpreted as a pointer, read from the row data area past the end of the 25-entry pointer array in a buffer allocated for 80x25 but accessed with 240x67 dimensions. Fix this by checking whether the console dimensions changed while in the alternate screen. If they did, free the stale saved buffer instead of restoring it. The unicode screen will be lazily rebuilt via vc_uniscr_check() when next needed.

In the Linux kernel, the following vulnerability has been resolved: crypto: tegra - Add missing CRYPTO_ALG_ASYNC The tegra crypto driver failed to set the CRYPTO_ALG_ASYNC on its asynchronous algorithms, causing the crypto API to select them for users that request only synchronous algorithms. This causes crashes (at least). Fix this by adding the flag like what the other drivers do. Also remove the unnecessary CRYPTO_ALG_TYPE_* flags, since those just get ignored and overridden by the registration function anyway.

In the Linux kernel, the following vulnerability has been resolved: iommupt: Fix short gather if the unmap goes into a large mapping unmap has the odd behavior that it can unmap more than requested if the ending point lands within the middle of a large or contiguous IOPTE. In this case the gather should flush everything unmapped which can be larger than what was requested to be unmapped. The gather was only flushing the range requested to be unmapped, not extending to the extra range, resulting in a short invalidation if the caller hits this special condition. This was found by the new invalidation/gather test I am adding in preparation for ARMv8. Claude deduced the root cause. As far as I remember nothing relies on unmapping a large entry, so this is likely not a triggerable bug.

In the Linux kernel, the following vulnerability has been resolved: thermal: core: Address thermal zone removal races with resume Since thermal_zone_pm_complete() and thermal_zone_device_resume() re-initialize the poll_queue delayed work for the given thermal zone, the cancel_delayed_work_sync() in thermal_zone_device_unregister() may miss some already running work items and the thermal zone may be freed prematurely [1]. There are two failing scenarios that both start with running thermal_pm_notify_complete() right before invoking thermal_zone_device_unregister() for one of the thermal zones. In the first scenario, there is a work item already running for the given thermal zone when thermal_pm_notify_complete() calls thermal_zone_pm_complete() for that thermal zone and it continues to run when thermal_zone_device_unregister() starts. Since the poll_queue delayed work has been re-initialized by thermal_pm_notify_complete(), the running work item will be missed by the cancel_delayed_work_sync() in thermal_zone_device_unregister() and if it continues to run past the freeing of the thermal zone object, a use-after-free will occur. In the second scenario, thermal_zone_device_resume() queued up by thermal_pm_notify_complete() runs right after the thermal_zone_exit() called by thermal_zone_device_unregister() has returned. The poll_queue delayed work is re-initialized by it before cancel_delayed_work_sync() is called by thermal_zone_device_unregister(), so it may continue to run after the freeing of the thermal zone object, which also leads to a use-after-free. Address the first failing scenario by ensuring that no thermal work items will be running when thermal_pm_notify_complete() is called. For this purpose, first move the cancel_delayed_work() call from thermal_zone_pm_complete() to thermal_zone_pm_prepare() to prevent new work from entering the workqueue going forward. Next, switch over to using a dedicated workqueue for thermal events and update the code in thermal_pm_notify() to flush that workqueue after thermal_pm_notify_prepare() has returned which will take care of all leftover thermal work already on the workqueue (that leftover work would do nothing useful anyway because all of the thermal zones have been flagged as suspended). The second failing scenario is addressed by adding a tz->state check to thermal_zone_device_resume() to prevent it from re-initializing the poll_queue delayed work if the thermal zone is going away. Note that the above changes will also facilitate relocating the suspend and resume of thermal zones closer to the suspend and resume of devices, respectively.

In the Linux kernel, the following vulnerability has been resolved: misc: fastrpc: possible double-free of cctx->remote_heap fastrpc_init_create_static_process() may free cctx->remote_heap on the err_map path but does not clear the pointer. Later, fastrpc_rpmsg_remove() frees cctx->remote_heap again if it is non-NULL, which can lead to a double-free if the INIT_CREATE_STATIC ioctl hits the error path and the rpmsg device is subsequently removed/unbound. Clear cctx->remote_heap after freeing it in the error path to prevent the later cleanup from freeing it again. This issue was found by an in-house analysis workflow that extracts AST-based information and runs static checks, with LLM assistance for triage, and was confirmed by manual code review. No hardware testing was performed.

In the Linux kernel, the following vulnerability has been resolved: usb: typec: ucsi: validate connector number in ucsi_notify_common() The connector number extracted from CCI via UCSI_CCI_CONNECTOR() is a 7-bit field (0-127) that is used to index into the connector array in ucsi_connector_change(). However, the array is only allocated for the number of connectors reported by the device (typically 2-4 entries). A malicious or malfunctioning device could report an out-of-range connector number in the CCI, causing an out-of-bounds array access in ucsi_connector_change(). Add a bounds check in ucsi_notify_common(), the central point where CCI is parsed after arriving from hardware, so that bogus connector numbers are rejected before they propagate further.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_uac1_legacy: validate control request size f_audio_complete() copies req->length bytes into a 4-byte stack variable: u32 data = 0; memcpy(&data, req->buf, req->length); req->length is derived from the host-controlled USB request path, which can lead to a stack out-of-bounds write. Validate req->actual against the expected payload size for the supported control selectors and decode only the expected amount of data. This avoids copying a host-influenced length into a fixed-size stack object.

In the Linux kernel, the following vulnerability has been resolved: crypto: krb5enc - fix async decrypt skipping hash verification krb5enc_dispatch_decrypt() sets req->base.complete as the skcipher callback, which is the caller's own completion handler. When the skcipher completes asynchronously, this signals "done" to the caller without executing krb5enc_dispatch_decrypt_hash(), completely bypassing the integrity verification (hash check). Compare with the encrypt path which correctly uses krb5enc_encrypt_done as an intermediate callback to chain into the hash computation on async completion. Fix by adding krb5enc_decrypt_done as an intermediate callback that chains into krb5enc_dispatch_decrypt_hash() upon async skcipher completion, matching the encrypt path's callback pattern. Also fix EBUSY/EINPROGRESS handling throughout: remove krb5enc_request_complete() which incorrectly swallowed EINPROGRESS notifications that must be passed up to callers waiting on backlogged requests, and add missing EBUSY checks in krb5enc_encrypt_ahash_done for the dispatch_encrypt return value. Unset MAY_BACKLOG on the async completion path so the user won't see back-to-back EINPROGRESS notifications.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate owner of durable handle on reconnect Currently, ksmbd does not verify if the user attempting to reconnect to a durable handle is the same user who originally opened the file. This allows any authenticated user to hijack an orphaned durable handle by predicting or brute-forcing the persistent ID. According to MS-SMB2, the server MUST verify that the SecurityContext of the reconnect request matches the SecurityContext associated with the existing open. Add a durable_owner structure to ksmbd_file to store the original opener's UID, GID, and account name. and catpure the owner information when a file handle becomes orphaned. and implementing ksmbd_vfs_compare_durable_owner() to validate the identity of the requester during SMB2_CREATE (DHnC).

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: validate rec->used in journal-replay file record check check_file_record() validates rec->total against the record size but never validates rec->used. The do_action() journal-replay handlers read rec->used from disk and use it to compute memmove lengths: DeleteAttribute: memmove(attr, ..., used - asize - roff) CreateAttribute: memmove(..., attr, used - roff) change_attr_size: memmove(..., used - PtrOffset(rec, next)) When rec->used is smaller than the offset of a validated attribute, or larger than the record size, these subtractions can underflow allowing us to copy huge amounts of memory in to a 4kb buffer, generally considered a bad idea overall. This requires a corrupted filesystem, which isn't a threat model the kernel really needs to worry about, but checking for such an obvious out-of-bounds value is good to keep things robust, especially on journal replay Fix this up by bounding rec->used correctly. This is much like commit b2bc7c44ed17 ("fs/ntfs3: Fix slab-out-of-bounds read in DeleteIndexEntryRoot") which checked different values in this same switch statement.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix UAF caused by decrementing sbi->nr_pages[] in f2fs_write_end_io() The xfstests case "generic/107" and syzbot have both reported a NULL pointer dereference. The concurrent scenario that triggers the panic is as follows: F2FS_WB_CP_DATA write callback umount - f2fs_write_checkpoint - f2fs_wait_on_all_pages(sbi, F2FS_WB_CP_DATA) - blk_mq_end_request - bio_endio - f2fs_write_end_io : dec_page_count(sbi, F2FS_WB_CP_DATA) : wake_up(&sbi->cp_wait) - kill_f2fs_super - kill_block_super - f2fs_put_super : iput(sbi->node_inode) : sbi->node_inode = NULL : f2fs_in_warm_node_list - is_node_folio // sbi->node_inode is NULL and panic The root cause is that f2fs_put_super() calls iput(sbi->node_inode) and sets sbi->node_inode to NULL after sbi->nr_pages[F2FS_WB_CP_DATA] is decremented to zero. As a result, f2fs_in_warm_node_list() may dereference a NULL node_inode when checking whether a folio belongs to the node inode, leading to a panic. This patch fixes the issue by calling f2fs_in_warm_node_list() before decrementing sbi->nr_pages[F2FS_WB_CP_DATA], thus preventing the use-after-free condition.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: require minimum ACE size in smb_check_perm_dacl() Both ACE-walk loops in smb_check_perm_dacl() only guard against an under-sized remaining buffer, not against an ACE whose declared `ace->size` is smaller than the struct it claims to describe: if (offsetof(struct smb_ace, access_req) > aces_size) break; ace_size = le16_to_cpu(ace->size); if (ace_size > aces_size) break; The first check only requires the 4-byte ACE header to be in bounds; it does not require access_req (4 bytes at offset 4) to be readable. An attacker who has set a crafted DACL on a file they own can declare ace->size == 4 with aces_size == 4, pass both checks, and then granted |= le32_to_cpu(ace->access_req); /* upper loop */ compare_sids(&sid, &ace->sid); /* lower loop */ reads access_req at offset 4 (OOB by up to 4 bytes) and ace->sid at offset 8 (OOB by up to CIFS_SID_BASE_SIZE + SID_MAX_SUB_AUTHORITIES * 4 bytes). Tighten both loops to require ace_size >= offsetof(struct smb_ace, sid) + CIFS_SID_BASE_SIZE which is the smallest valid on-wire ACE layout (4-byte header + 4-byte access_req + 8-byte sid base with zero sub-auths). Also reject ACEs whose sid.num_subauth exceeds SID_MAX_SUB_AUTHORITIES before letting compare_sids() dereference sub_auth[] entries. parse_sec_desc() already enforces an equivalent check (lines 441-448); smb_check_perm_dacl() simply grew weaker validation over time. Reachability: authenticated SMB client with permission to set an ACL on a file. On a subsequent CREATE against that file, the kernel walks the stored DACL via smb_check_perm_dacl() and triggers the OOB read. Not pre-auth, and the OOB read is not reflected to the attacker, but KASAN reports and kernel state corruption are possible.

In the Linux kernel, the following vulnerability has been resolved: smb: server: fix active_num_conn leak on transport allocation failure Commit 77ffbcac4e56 ("smb: server: fix leak of active_num_conn in ksmbd_tcp_new_connection()") addressed the kthread_run() failure path. The earlier alloc_transport() == NULL path in the same function has the same leak, is reachable pre-authentication via any TCP connect to port 445, and was empirically reproduced on UML (ARCH=um, v7.0-rc7): a small number of forced allocation failures were sufficient to put ksmbd into a state where every subsequent connection attempt was rejected for the remainder of the boot. ksmbd_kthread_fn() increments active_num_conn before calling ksmbd_tcp_new_connection() and discards the return value, so when alloc_transport() returns NULL the socket is released and -ENOMEM returned without decrementing the counter. Each such failure permanently consumes one slot from the max_connections pool; once cumulative failures reach the cap, atomic_inc_return() hits the threshold on every subsequent accept and every new connection is rejected. The counter is only reset by module reload. An unauthenticated remote attacker can drive the server toward the memory pressure that makes alloc_transport() fail by holding open connections with large RFC1002 lengths up to MAX_STREAM_PROT_LEN (0x00FFFFFF); natural transient allocation failures on a loaded host produce the same drift more slowly. Mirror the existing rollback pattern in ksmbd_kthread_fn(): on the alloc_transport() failure path, decrement active_num_conn gated on server_conf.max_connections. Repro details: with the patch reverted, forced alloc_transport() NULL returns leaked counter slots and subsequent connection attempts -- including legitimate connects issued after the forced-fail window had closed -- were all rejected with "Limit the maximum number of connections". With this patch applied, the same connect sequence produces no rejections and the counter cycles cleanly between zero and one on every accept.

In the Linux kernel, the following vulnerability has been resolved: smb: client: validate the whole DACL before rewriting it in cifsacl build_sec_desc() and id_mode_to_cifs_acl() derive a DACL pointer from a server-supplied dacloffset and then use the incoming ACL to rebuild the chmod/chown security descriptor. The original fix only checked that the struct smb_acl header fits before reading dacl_ptr->size or dacl_ptr->num_aces. That avoids the immediate header-field OOB read, but the rewrite helpers still walk ACEs based on pdacl->num_aces with no structural validation of the incoming DACL body. A malicious server can return a truncated DACL that still contains a header, claims one or more ACEs, and then drive replace_sids_and_copy_aces() or set_chmod_dacl() past the validated extent while they compare or copy attacker-controlled ACEs. Factor the DACL structural checks into validate_dacl(), extend them to validate each ACE against the DACL bounds, and use the shared validator before the chmod/chown rebuild paths. parse_dacl() reuses the same validator so the read-side parser and write-side rewrite paths agree on what constitutes a well-formed incoming DACL.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix OOB read in smb2_ioctl_query_info QUERY_INFO path smb2_ioctl_query_info() has two response-copy branches: PASSTHRU_FSCTL and the default QUERY_INFO path. The QUERY_INFO branch clamps qi.input_buffer_length to the server-reported OutputBufferLength and then copies qi.input_buffer_length bytes from qi_rsp->Buffer to userspace, but it never verifies that the flexible-array payload actually fits within rsp_iov[1].iov_len. A malicious server can return OutputBufferLength larger than the actual QUERY_INFO response, causing copy_to_user() to walk past the response buffer and expose adjacent kernel heap to userspace. Guard the QUERY_INFO copy with a bounds check on the actual Buffer payload. Use struct_size(qi_rsp, Buffer, qi.input_buffer_length) rather than an open-coded addition so the guard cannot overflow on 32-bit builds.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate response sizes in ipc_validate_msg() ipc_validate_msg() computes the expected message size for each response type by adding (or multiplying) attacker-controlled fields from the daemon response to a fixed struct size in unsigned int arithmetic. Three cases can overflow: KSMBD_EVENT_RPC_REQUEST: msg_sz = sizeof(struct ksmbd_rpc_command) + resp->payload_sz; KSMBD_EVENT_SHARE_CONFIG_REQUEST: msg_sz = sizeof(struct ksmbd_share_config_response) + resp->payload_sz; KSMBD_EVENT_LOGIN_REQUEST_EXT: msg_sz = sizeof(struct ksmbd_login_response_ext) + resp->ngroups * sizeof(gid_t); resp->payload_sz is __u32 and resp->ngroups is __s32. Each addition can wrap in unsigned int; the multiplication by sizeof(gid_t) mixes signed and size_t, so a negative ngroups is converted to SIZE_MAX before the multiply. A wrapped value of msg_sz that happens to equal entry->msg_sz bypasses the size check on the next line, and downstream consumers (smb2pdu.c:6742 memcpy using rpc_resp->payload_sz, kmemdup in ksmbd_alloc_user using resp_ext->ngroups) then trust the unverified length. Use check_add_overflow() on the RPC_REQUEST and SHARE_CONFIG_REQUEST paths to detect integer overflow without constraining functional payload size; userspace ksmbd-tools grows NDR responses in 4096-byte chunks for calls like NetShareEnumAll, so a hard transport cap is unworkable on the response side. For LOGIN_REQUEST_EXT, reject resp->ngroups outside the signed [0, NGROUPS_MAX] range up front and report the error from ipc_validate_msg() so it fires at the IPC boundary; with that bound the subsequent multiplication and addition stay well below UINT_MAX. The now-redundant ngroups check and pr_err in ksmbd_alloc_user() are removed. This is the response-side analogue of aab98e2dbd64 ("ksmbd: fix integer overflows on 32 bit systems"), which hardened the request side.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate num_aces and harden ACE walk in smb_inherit_dacl() smb_inherit_dacl() trusts the on-disk num_aces value from the parent directory's DACL xattr and uses it to size a heap allocation: aces_base = kmalloc(sizeof(struct smb_ace) * num_aces * 2, ...); num_aces is a u16 read from le16_to_cpu(parent_pdacl->num_aces) without checking that it is consistent with the declared pdacl_size. An authenticated client whose parent directory's security.NTACL is tampered (e.g. via offline xattr corruption or a concurrent path that bypasses parse_dacl()) can present num_aces = 65535 with minimal actual ACE data. This causes a ~8 MB allocation (not kzalloc, so uninitialized) that the subsequent loop only partially populates, and may also overflow the three-way size_t multiply on 32-bit kernels. Additionally, the ACE walk loop uses the weaker offsetof(struct smb_ace, access_req) minimum size check rather than the minimum valid on-wire ACE size, and does not reject ACEs whose declared size is below the minimum. Reproduced on UML + KASAN + LOCKDEP against the real ksmbd code path. A legitimate mount.cifs client creates a parent directory over SMB (ksmbd writes a valid security.NTACL xattr), then the NTACL blob on the backing filesystem is rewritten to set num_aces = 0xFFFF while keeping the posix_acl_hash bytes intact so ksmbd_vfs_get_sd_xattr()'s hash check still passes. A subsequent SMB2 CREATE of a child under that parent drives smb2_open() into smb_inherit_dacl() (share has "vfs objects = acl_xattr" set), which fails the page allocator: WARNING: mm/page_alloc.c:5226 at __alloc_frozen_pages_noprof+0x46c/0x9c0 Workqueue: ksmbd-io handle_ksmbd_work __alloc_frozen_pages_noprof+0x46c/0x9c0 ___kmalloc_large_node+0x68/0x130 __kmalloc_large_node_noprof+0x24/0x70 __kmalloc_noprof+0x4c9/0x690 smb_inherit_dacl+0x394/0x2430 smb2_open+0x595d/0xabe0 handle_ksmbd_work+0x3d3/0x1140 With the patch applied the added guard rejects the tampered value with -EINVAL before any large allocation runs, smb2_open() falls back to smb2_create_sd_buffer(), and the child is created with a default SD. No warning, no splat. Fix by: 1. Validating num_aces against pdacl_size using the same formula applied in parse_dacl(). 2. Replacing the raw kmalloc(sizeof * num_aces * 2) with kmalloc_array(num_aces * 2, sizeof(...)) for overflow-safe allocation. 3. Tightening the per-ACE loop guard to require the minimum valid ACE size (offsetof(smb_ace, sid) + CIFS_SID_BASE_SIZE) and rejecting under-sized ACEs, matching the hardening in smb_check_perm_dacl() and parse_dacl(). v1 -> v2: - Replace the synthetic test-module splat in the changelog with a real-path UML + KASAN reproduction driven through mount.cifs and SMB2 CREATE; Namjae flagged the kcifs3_test_inherit_dacl_old name in v1 since it does not exist in ksmbd. - Drop the commit-hash citation from the code comment per Namjae's review; keep the parse_dacl() pointer.

In the Linux kernel, the following vulnerability has been resolved: writeback: Fix use after free in inode_switch_wbs_work_fn() inode_switch_wbs_work_fn() has a loop like: wb_get(new_wb); while (1) { list = llist_del_all(&new_wb->switch_wbs_ctxs); /* Nothing to do? */ if (!list) break; ... process the items ... } Now adding of items to the list looks like: wb_queue_isw() if (llist_add(&isw->list, &wb->switch_wbs_ctxs)) queue_work(isw_wq, &wb->switch_work); Because inode_switch_wbs_work_fn() loops when processing isw items, it can happen that wb->switch_work is pending while wb->switch_wbs_ctxs is empty. This is a problem because in that case wb can get freed (no isw items -> no wb reference) while the work is still pending causing use-after-free issues. We cannot just fix this by cancelling work when freeing wb because that could still trigger problematic 0 -> 1 transitions on wb refcount due to wb_get() in inode_switch_wbs_work_fn(). It could be all handled with more careful code but that seems unnecessarily complex so let's avoid that until it is proven that the looping actually brings practical benefit. Just remove the loop from inode_switch_wbs_work_fn() instead. That way when wb_queue_isw() queues work, we are guaranteed we have added the first item to wb->switch_wbs_ctxs and nobody is going to remove it (and drop the wb reference it holds) until the queued work runs.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix use-after-free of sbi in f2fs_compress_write_end_io() In f2fs_compress_write_end_io(), dec_page_count(sbi, type) can bring the F2FS_WB_CP_DATA counter to zero, unblocking f2fs_wait_on_all_pages() in f2fs_put_super() on a concurrent unmount CPU. The unmount path then proceeds to call f2fs_destroy_page_array_cache(sbi), which destroys sbi->page_array_slab via kmem_cache_destroy(), and eventually kfree(sbi). Meanwhile, the bio completion callback is still executing: when it reaches page_array_free(sbi, ...), it dereferences sbi->page_array_slab — a destroyed slab cache — to call kmem_cache_free(), causing a use-after-free. This is the same class of bug as CVE-2026-23234 (which fixed the equivalent race in f2fs_write_end_io() in data.c), but in the compressed writeback completion path that was not covered by that fix. Fix this by moving dec_page_count() to after page_array_free(), so that all sbi accesses complete before the counter decrement that can unblock unmount. For non-last folios (where atomic_dec_return on cic->pending_pages is nonzero), dec_page_count is called immediately before returning — page_array_free is not reached on this path, so there is no post-decrement sbi access. For the last folio, page_array_free runs while the F2FS_WB_CP_DATA counter is still nonzero (this folio has not yet decremented it), keeping sbi alive, and dec_page_count runs as the final operation.

In the Linux kernel, the following vulnerability has been resolved: net/packet: fix TOCTOU race on mmap'd vnet_hdr in tpacket_snd() In tpacket_snd(), when PACKET_VNET_HDR is enabled, vnet_hdr points directly into the mmap'd TX ring buffer shared with userspace. The kernel validates the header via __packet_snd_vnet_parse() but then re-reads all fields later in virtio_net_hdr_to_skb(). A concurrent userspace thread can modify the vnet_hdr fields between validation and use, bypassing all safety checks. The non-TPACKET path (packet_snd()) already correctly copies vnet_hdr to a stack-local variable. All other vnet_hdr consumers in the kernel (tun.c, tap.c, virtio_net.c) also use stack copies. The TPACKET TX path is the only caller of virtio_net_hdr_to_skb() that reads directly from user-controlled shared memory. Fix this by copying vnet_hdr from the mmap'd ring buffer to a stack-local variable before validation and use, consistent with the approach used in packet_snd() and all other callers.

In the Linux kernel, the following vulnerability has been resolved: crypto: ccp: Don't attempt to copy CSR to userspace if PSP command failed When retrieving the PEK CSR, don't attempt to copy the blob to userspace if the firmware command failed. If the failure was due to an invalid length, i.e. the userspace buffer+length was too small, copying the number of bytes _firmware_ requires will overflow the kernel-allocated buffer and leak data to userspace. BUG: KASAN: slab-out-of-bounds in instrument_copy_to_user ../include/linux/instrumented.h:129 [inline] BUG: KASAN: slab-out-of-bounds in _inline_copy_to_user ../include/linux/uaccess.h:205 [inline] BUG: KASAN: slab-out-of-bounds in _copy_to_user+0x66/0xa0 ../lib/usercopy.c:26 Read of size 2084 at addr ffff898144612e20 by task syz.9.219/21405 CPU: 14 UID: 0 PID: 21405 Comm: syz.9.219 Tainted: G U O 7.0.0-smp-DEV #28 PREEMPTLAZY Tainted: [U]=USER, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 12.62.0-0 11/19/2025 Call Trace: <TASK> dump_stack_lvl+0xc5/0x110 ../lib/dump_stack.c:120 print_address_description ../mm/kasan/report.c:378 [inline] print_report+0xbc/0x260 ../mm/kasan/report.c:482 kasan_report+0xa2/0xe0 ../mm/kasan/report.c:595 check_region_inline ../mm/kasan/generic.c:-1 [inline] kasan_check_range+0x264/0x2c0 ../mm/kasan/generic.c:200 instrument_copy_to_user ../include/linux/instrumented.h:129 [inline] _inline_copy_to_user ../include/linux/uaccess.h:205 [inline] _copy_to_user+0x66/0xa0 ../lib/usercopy.c:26 copy_to_user ../include/linux/uaccess.h:236 [inline] sev_ioctl_do_pek_csr+0x31f/0x590 ../drivers/crypto/ccp/sev-dev.c:1872 sev_ioctl+0x3a4/0x490 ../drivers/crypto/ccp/sev-dev.c:2562 vfs_ioctl ../fs/ioctl.c:51 [inline] __do_sys_ioctl ../fs/ioctl.c:597 [inline] __se_sys_ioctl+0x11d/0x1b0 ../fs/ioctl.c:583 do_syscall_x64 ../arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xe0/0x800 ../arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> WARN if the driver says the command succeeded, but the firmware error code says otherwise, as __sev_do_cmd_locked() is expected to return -EIO on any firwmware error.

In the Linux kernel, the following vulnerability has been resolved: crypto: ccp: Don't attempt to copy PDH cert to userspace if PSP command failed When retrieving the PDH cert, don't attempt to copy the blobs to userspace if the firmware command failed. If the failure was due to an invalid length, i.e. the userspace buffer+length was too small, copying the number of bytes _firmware_ requires will overflow the kernel-allocated buffer and leak data to userspace. BUG: KASAN: slab-out-of-bounds in instrument_copy_to_user ../include/linux/instrumented.h:129 [inline] BUG: KASAN: slab-out-of-bounds in _inline_copy_to_user ../include/linux/uaccess.h:205 [inline] BUG: KASAN: slab-out-of-bounds in _copy_to_user+0x66/0xa0 ../lib/usercopy.c:26 Read of size 2084 at addr ffff8885c4ab8aa0 by task syz.0.186/21033 CPU: 51 UID: 0 PID: 21033 Comm: syz.0.186 Tainted: G U O 7.0.0-smp-DEV #28 PREEMPTLAZY Tainted: [U]=USER, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 34.84.12-0 11/17/2025 Call Trace: <TASK> dump_stack_lvl+0xc5/0x110 ../lib/dump_stack.c:120 print_address_description ../mm/kasan/report.c:378 [inline] print_report+0xbc/0x260 ../mm/kasan/report.c:482 kasan_report+0xa2/0xe0 ../mm/kasan/report.c:595 check_region_inline ../mm/kasan/generic.c:-1 [inline] kasan_check_range+0x264/0x2c0 ../mm/kasan/generic.c:200 instrument_copy_to_user ../include/linux/instrumented.h:129 [inline] _inline_copy_to_user ../include/linux/uaccess.h:205 [inline] _copy_to_user+0x66/0xa0 ../lib/usercopy.c:26 copy_to_user ../include/linux/uaccess.h:236 [inline] sev_ioctl_do_pdh_export+0x3d3/0x7c0 ../drivers/crypto/ccp/sev-dev.c:2347 sev_ioctl+0x2a2/0x490 ../drivers/crypto/ccp/sev-dev.c:2568 vfs_ioctl ../fs/ioctl.c:51 [inline] __do_sys_ioctl ../fs/ioctl.c:597 [inline] __se_sys_ioctl+0x11d/0x1b0 ../fs/ioctl.c:583 do_syscall_x64 ../arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xe0/0x800 ../arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> WARN if the driver says the command succeeded, but the firmware error code says otherwise, as __sev_do_cmd_locked() is expected to return -EIO on any firwmware error.