CVE Database

In the Linux kernel, the following vulnerability has been resolved: wifi: wilc1000: fix dma_buffer leak on bus acquire failure wilc_wlan_firmware_download() allocates dma_buffer with kmalloc() at the top of the function and uses a 'fail:' label to free it via kfree(dma_buffer) on error. All later error paths correctly use 'goto fail' to route through this cleanup. However, the early failure path after the first acquire_bus() call uses a bare 'return ret;', which leaks dma_buffer whenever the bus acquire fails. Replace the early return with goto fail so the existing cleanup path runs. Found via a custom Coccinelle semantic patch hunting for kmalloc'd locals leaked on early-return error paths in driver firmware-download code.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix null pointer dereference in compare_guid_key() session_fd_check() walks the per-inode m_op_list during durable-handle session teardown and sets op->conn = NULL for every opinfo whose conn matched the closing session's connection. The matching opinfo, however, stays linked in its per-ClientGuid lease_table_list entry's lb->lease_list because destroy_lease_table() only runs on full TCP-connection teardown, not on SESSION_LOGOFF. If the same TCP connection then negotiates a fresh session with the same ClientGuid (ClientGuid is bound to NEGOTIATE, not the session, and is unchanged across LOGOFF + SETUP) and issues a SMB2 CREATE with a lease context on a different inode, find_same_lease_key() walks lb->lease_list, reaches the stale opinfo, and calls compare_guid_key(), which unconditionally dereferences opinfo->conn->ClientGUID. The conn pointer is NULL and the kernel panics. Reproducer requires only a successful SMB2 SESSION_SETUP and a share configured with 'durable handles = yes'. KASAN report on mainline 70390501d194: general protection fault, probably for non-canonical address 0xdffffc0000000069: 0000 [#1] SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000348-0x000000000000034f] Workqueue: ksmbd-io handle_ksmbd_work RIP: 0010:bcmp+0x5b/0x230 Call Trace: compare_guid_key+0x4b/0xd0 find_same_lease_key+0x324/0x690 smb2_open+0x6aea/0x8e60 handle_ksmbd_work+0x796/0xee0 ... Faulting address 0x348 is the offset of ClientGUID within struct ksmbd_conn, confirming opinfo->conn was NULL. Read opinfo->conn once and bail out if it has been cleared by a concurrent session_fd_check(). A half-detached opinfo cannot be the owner of an active lease, so returning 0 is the correct match result.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix null pointer dereference in proc_show_files() When a SMB2 client opens a file with a durable v2 handle and then issues SMB2 SESSION_LOGOFF, session_fd_check() clears fp->tcon = NULL on the reconnectable file pointer but leaves the fp registered in global_ft.idr until the durable scavenger fires (up to fp->durable_timeout seconds later). During that window any read of /proc/fs/ksmbd/files (mode 0400) panics the kernel because proc_show_files() walks global_ft.idr and unconditionally dereferences fp->tcon->id with no NULL guard. Reproducer requires only a successful SMB2 SESSION_SETUP and a share configured with 'durable handles = yes'. KASAN report on mainline 70390501d194: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] RIP: 0010:proc_show_files+0x118/0x740 Call Trace: proc_show_files+0x118/0x740 seq_read_iter+0x4ef/0xe10 proc_reg_read_iter+0x1b7/0x280 ... Guard the dereference. A durable-disconnected fp legitimately has no tcon; report its tree id as 0 rather than oopsing.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate SID in parent security descriptor during ACL inheritance Introduce smb_validate_ntsd_sid() helper to safely validate Owner SID and Group SID inside the NT Security Descriptor (smb_ntsd) retrieved from the parent directory.

In the Linux kernel, the following vulnerability has been resolved: smb: client: require net admin for CIFS SWN netlink CIFS_GENL_CMD_SWN_NOTIFY is the userspace witness-notify command. The intended sender is the cifs.witness helper, but the generic-netlink operation currently has no capability flag, so any local process can send RESOURCE_CHANGE or CLIENT_MOVE notifications to the in-kernel witness handler. The same family exposes CIFS_GENL_MCGRP_SWN without multicast-group capability flags. Register messages sent to that group include the witness registration id and, for NTLM-authenticated mounts, the username, domain, and password attributes copied from the CIFS session. An unprivileged local process should not be able to join that group and receive those messages. Require CAP_NET_ADMIN for incoming SWN_NOTIFY commands with GENL_ADMIN_PERM, and require CAP_NET_ADMIN over the network namespace for joining the SWN multicast group with GENL_MCAST_CAP_NET_ADMIN. The cifs.witness service runs with the privileges needed for both operations.

In the Linux kernel, the following vulnerability has been resolved: ALSA: pcm: Don't setup bogus iov_iter for silencing At transition to the iov_iter for PCM data transfer, we blindly applied the iov_iter setup also for silencing (i.e. data = NULL), and it leads to a calculation of bogus iov_iter. Fortunately this didn't cause troubles on most of architectures but it goes wrong on RISC-V now, causing a NULL dereference. Handle the NULL data case to treat the silencing in interleaved_copy() for addressing the bug above. noninterleaved_copy() has already the NULL data handling, so it doesn't need changes.

In the Linux kernel, the following vulnerability has been resolved: ALSA: asihpi: Fix potential OOB array access at reading cache find_control() to retrieve a cached info accesses the array with the given index blindly, which may lead to an OOB array access. Add a sanity check for avoiding it.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: MGMT: validate Add Extended Advertising Data length MGMT_OP_ADD_EXT_ADV_DATA is registered as a variable-length command, with MGMT_ADD_EXT_ADV_DATA_SIZE as the fixed header size. The handler then uses cp->adv_data_len and cp->scan_rsp_len to validate and copy cp->data, but it never checks that those bytes are part of the mgmt command payload. A short command can therefore make add_ext_adv_data() pass an out-of-bounds pointer into tlv_data_is_valid(). If the bytes beyond the command buffer are addressable, they can also be copied into the advertising instance as scan response data, where the caller can read them back via MGMT_OP_GET_ADV_INSTANCE. The trigger requires CAP_NET_ADMIN in the initial user namespace; KASAN reports an 8-byte slab-out-of-bounds read. Reject commands whose length does not match the fixed header plus both advertising data lengths before parsing cp->data.

In the Linux kernel, the following vulnerability has been resolved: net: devmem: reject dma-buf bind with non-page-aligned size or SG length net_devmem_bind_dmabuf() trusts dmabuf->size and sg_dma_len() to be PAGE_SIZE multiples without checking: - tx_vec is sized dmabuf->size / PAGE_SIZE, and net_devmem_get_niov_at() only bounds-checks virt_addr < dmabuf->size before indexing tx_vec[virt_addr / PAGE_SIZE]. With size = N*PAGE_SIZE + r (1 <= r < PAGE_SIZE), sendmsg() at iov_base = N*PAGE_SIZE passes the bound check and reads tx_vec[N] -- one past. - owner->area.num_niovs = len / PAGE_SIZE while gen_pool_add_owner() covers the full byte len, so a non-page-multiple non-final sg desyncs num_niovs from the gen_pool region for every later sg, on both RX and TX. dma-buf does not require page-aligned sizes, so the bind path has to enforce what its own indexing assumes. Reject both with -EINVAL. The size check is TX-only (only tx_vec is sized off dmabuf->size); the SG-length check covers both directions.

In the Linux kernel, the following vulnerability has been resolved: net: hsr: defer node table free until after RCU readers HSR node-list and node-status generic-netlink operations run under rcu_read_lock(). They walk hsr->node_db through hsr_get_next_node() and hsr_get_node_data(), but RTM_DELLINK teardown removes the same node table with plain list_del() and frees each node immediately. That lets a generic-netlink reader hold a struct hsr_node pointer across hsr_dellink(). In a KASAN build, widening the reader window after hsr_get_next_node() obtains the node reproduces a slab-use-after-free when the reader copies node->macaddress_A; the freeing stack is hsr_del_nodes() from hsr_dellink(). Use list_del_rcu() and defer the free through the existing hsr_free_node_rcu() callback. This matches the lifetime rule used by the HSR prune paths, which already delete nodes with list_del_rcu() and call_rcu().

In the Linux kernel, the following vulnerability has been resolved: net: ifb: report ethtool stats over num_tx_queues ifb_dev_init() allocates dp->tx_private to dev->num_tx_queues entries via kzalloc_objs(*txp, dev->num_tx_queues). Both IFB per-queue RX and TX stats live in those entries: ifb_xmit() updates txp->rx_stats using the skb queue mapping, ifb_ri_tasklet() updates txp->tx_stats, and ifb_stats64() aggregates both over dev->num_tx_queues. The ethtool stats callbacks instead size and walk the per-queue stats with dev->real_num_rx_queues and dev->real_num_tx_queues. With an asymmetric device where the RX queue count exceeds the TX queue count, for example: ip link add name ifb10 numtxqueues 1 numrxqueues 8 type ifb ethtool -S ifb10 ifb_get_ethtool_stats() indexes past the tx_private allocation and copies adjacent slab data through ETHTOOL_GSTATS. Use dev->num_tx_queues consistently for the stats strings, the stats count, and the stats data walks. This reports one RX stats group and one TX stats group for each backing ifb_q_private entry, which is the queue set IFB can actually populate. Reproduced under UML+KASAN at v7.1-rc2: BUG: KASAN: slab-out-of-bounds in ifb_fill_stats_data+0x3c/0xae Read of size 8 at addr 0000000062dbd228 by task ethtool/36 ifb_fill_stats_data+0x3c/0xae ifb_get_ethtool_stats+0xc0/0x129 __dev_ethtool+0x1ca5/0x363c dev_ethtool+0x123/0x1b3 dev_ioctl+0x56c/0x744 sock_do_ioctl+0x15f/0x1b2 sock_ioctl+0x4d5/0x50a sys_ioctl+0xd8b/0xde9 With the patch applied, the same UML+KASAN repro is silent and ethtool -S ifb10 reports only the stats backed by the single allocated tx_private entry.

In the Linux kernel, the following vulnerability has been resolved: qed: fix double free in qed_cxt_tables_alloc() If one of the later PF or VF CID bitmap allocations fails, qed_cid_map_alloc() jumps to cid_map_fail and frees the previously allocated CID bitmaps before returning an error. qed_cxt_tables_alloc() then calls qed_cxt_mngr_free(), which invokes qed_cid_map_free() again. Fix this by setting each CID bitmap pointer to NULL after bitmap_free() to avoid double free. The bug was first flagged by an experimental analysis tool we are developing for kernel memory-management bugs while analyzing v6.13-rc1. The tool is still under development and is not yet publicly available. Manual inspection confirms that the bug is still present in v7.1-rc3. Runtime reproduction was not attempted because exercising the failing allocation path requires device-specific setup.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: capture fast-RX rate before mesh reuses skb->cb ieee80211_invoke_fast_rx() reads RX status through IEEE80211_SKB_RXCB(skb), which aliases the same skb->cb storage that ieee80211_rx_mesh_data() reuses as IEEE80211_TX_INFO. In the unicast forward path, mesh_data does: info = IEEE80211_SKB_CB(fwd_skb); memset(info, 0, sizeof(*info)); on the same skb the caller still names via rx->skb, then either queues the skb for TX (success) or kfree_skb()'s it (no-route) before returning RX_QUEUED. The caller's RX_QUEUED arm then calls sta_stats_encode_rate(status) on memory that is either zeroed (success path) or freed (no-route path). The latter is KASAN slab-use-after-free in ieee80211_prepare_and_rx_handle. Fix by encoding the rate from status before invoking ieee80211_rx_mesh_data(), so the RX_QUEUED arm consumes a value captured while status was still backed by valid memory.

In the Linux kernel, the following vulnerability has been resolved: ipv6: ioam: add NULL check for idev in ipv6_hop_ioam() Reported by Sashiko: The function ipv6_hop_ioam() accesses __in6_dev_get(skb->dev)->cnf.ioam6_enabled without validating the returned idev pointer. Because addrconf_ifdown() can concurrently clear dev->ip6_ptr via RCU, __in6_dev_get() can return NULL during interface teardown, which could cause a NULL pointer dereference when processing an IOAM Hop-by-Hop option. Let's add a check and use SKB_DROP_REASON_IPV6DISABLED accordingly.

In the Linux kernel, the following vulnerability has been resolved: vsock/vmci: fix UAF when peer resets connection during handshake vmci_transport_recv_connecting_server() returned err = 0 for a peer RST in its default switch arm: err = pkt->type == VMCI_TRANSPORT_PACKET_TYPE_RST ? 0 : -EINVAL; That made vmci_transport_recv_listen() skip vsock_remove_pending(), leaving the pending socket on the listener's pending_links with sk_state = TCP_CLOSE while destroy: still dropped the explicit reference taken before schedule_delayed_work(). One second later vsock_pending_work() observed is_pending=true and performed full cleanup: vsock_remove_pending() then the two trailing sock_put(sk) calls -- the first reached refcount 0 and __sk_freed the socket, and the second wrote into the freed object: BUG: KASAN: slab-use-after-free in refcount_warn_saturate Write of size 4 at addr ffff88800b1cac80 by task kworker Workqueue: events vsock_pending_work Treat peer RST like any other unexpected packet type (err = -EINVAL). All destroy: arms now return err < 0, so vmci_transport_recv_listen() removes pending from pending_links synchronously and vsock_pending_work() takes the is_pending=false / !rejected branch, dropping only its own work reference. This also closes the multi-packet race Sashiko reported on v2: pending is removed from the list before any subsequent packet can find it. The pre-existing sk_acceptq_removed() gap on the err < 0 path of vmci_transport_recv_listen() that Sashiko also noted is not introduced or changed by this patch. Tested on lts-6.12.79 with KASAN: 52/100 unpatched -> 0/100 patched.

In the Linux kernel, the following vulnerability has been resolved: ipv4: raw: reject IP_HDRINCL packets with ihl < 5 raw_send_hdrinc() validates that the caller-supplied IPv4 header fits within the message length: iphlen = iph->ihl * 4; err = -EINVAL; if (iphlen > length) goto error_free; if (iphlen >= sizeof(*iph)) { /* fix up saddr, tot_len, id, csum, transport_header */ } It does not, however, reject ihl < 5. For such a packet the "if (iphlen >= sizeof(*iph))" branch is skipped, leaving the crafted iphdr untouched, but the packet is still handed to __ip_local_out() and onward. Downstream consumers that read iph->ihl assume a sane value: net/ipv4/ah4.c:ah_output() in particular subtracts sizeof(struct iphdr) from top_iph->ihl * 4 and passes the (signed-int-negative, then cast to size_t) result to memcpy(), producing an OOB access of length close to SIZE_MAX and a host kernel panic. An IPv4 header with ihl < 5 is malformed by definition (RFC 791: "Internet Header Length is the length of the internet header in 32 bit words ... Note that the minimum value for a correct header is 5."). The kernel should not be willing to inject such a packet into its own output path. Reject "iphlen < sizeof(*iph)" alongside the existing "iphlen > length" check. This matches the principle that locally constructed packets that re-enter the IP stack must pass the same basic sanity tests that a foreign packet would be subjected to. Once this lands, the "if (iphlen >= sizeof(*iph))" wrapper around the fixup branch becomes redundant; left in place to keep the patch minimal and backport-friendly. A follow-up can unwrap it. Note that commit 86f4c90a1c5c ("ipv4, ipv6: ensure raw socket message is big enough to hold an IP header") ensures the message buffer is large enough to hold an iphdr, but does not constrain the self-reported iph->ihl. Reachability: the malformed packet source is any caller with CAP_NET_RAW, including an unprivileged process in a user+net namespace on a kernel with CONFIG_USER_NS=y. The reproduced AH crash also requires a matching xfrm AH policy on the outgoing route; a container granted CAP_NET_ADMIN can install that state and policy in its netns. Loopback bypasses xfrm_output, so the trigger uses a real netdev. Reproduced on UML + KASAN: kernel-mode fault at addr 0x0 with memcpy_orig at the crash site. Same shape reproduces inside a rootless Docker container with --cap-add NET_ADMIN on a stock distro kernel.

In the Linux kernel, the following vulnerability has been resolved: rbd: eliminate a race in lock_dwork draining on unmap Given how rbd_lock_add_request() and rbd_img_exclusive_lock() are written, lock_dwork may be (re)queued more than it's actually needed: for example in case a new I/O request comes in while we are in the middle of rbd_acquire_lock() on behalf of another I/O request. This is expected and with rbd_release_lock() preemptively canceling lock_dwork is benign under normal operation. A more problematic example is maybe_kick_acquire(): if (have_requests || delayed_work_pending(&rbd_dev->lock_dwork)) { dout("%s rbd_dev %p kicking lock_dwork\n", __func__, rbd_dev); mod_delayed_work(rbd_dev->task_wq, &rbd_dev->lock_dwork, 0); } It's not unrealistic for lock_dwork to get canceled right after delayed_work_pending() returns true and for mod_delayed_work() to requeue it right there anyway. This is a classic TOCTOU race. When it comes to unmapping the image, there is an implicit assumption of no self-initiated exclusive lock activity past the point of return from rbd_dev_image_unlock() which unlocks the lock if it happens to be held. This unlock is assumed to be final and lock_dwork (as well as all other exclusive lock tasks, really) isn't expected to get queued again. However, lock_dwork is canceled only in cancel_tasks_sync() (i.e. later in the unmap sequence) and on top of that the cancellation can get in effect nullified by maybe_kick_acquire(). This may result in rbd_acquire_lock() executing after rbd_dev_device_release() and rbd_dev_image_release() run and free and/or reset a bunch of things. One of the possible failure modes then is a violated rbd_assert(rbd_image_format_valid(rbd_dev->image_format)); in rbd_dev_header_info() which is called via rbd_dev_refresh() from rbd_post_acquire_action(). Redo exclusive lock task draining to provide saner semantics and try to meet the assumptions around rbd_dev_image_unlock().

In the Linux kernel, the following vulnerability has been resolved: lsm: hold cred_guard_mutex for lsm_set_self_attr() Just as proc_pid_attr_write() already does before calling the LSM hook. This only matters for SELinux and AppArmor which check whether the process is being ptraced and if so, whether to allow the transition.

In the Linux kernel, the following vulnerability has been resolved: af_unix: Fix UAF read of tail->len in unix_stream_data_wait() unix_stream_data_wait() does skb_peek_tail(&sk->sk_receive_queue) without holding any lock that prevents SKBs on that queue from being dequeued and freed. This has been the case since commit 79f632c71bea ("unix/stream: fix peeking with an offset larger than data in queue"). The first consequence of this is that the pointer comparison `tail != last` can be false even if `last` semantically refers to an already-freed SKB while `tail` is a new SKB allocated at the same address; which can cause unix_stream_data_wait() to wrongly keep blocking after new data has arrived, but only in a weird scenario where a peeking recv() and a normal recv() on the same socket are racing, which is probably not a real problem. But since commit 2b514574f7e8 ("net: af_unix: implement splice for stream af_unix sockets"), `tail` is actually dereferenced, which can cause UAF in the following race scenario (where test_setup() runs single-threaded, and afterwards, test_thread1() and test_thread2() run concurrently in two threads: ``` static int socks[2]; void test_setup(void) { socketpair(AF_UNIX, SOCK_STREAM, 0, socks); send(socks[1], "A", 1, 0); int peekoff = 1; setsockopt(socks[0], SOL_SOCKET, SO_PEEK_OFF, &peekoff, sizeof(peekoff)); } void test_thread1(void) { char dummy; recv(socks[0], &dummy, 1, MSG_PEEK); } void test_thread2(void) { char dummy; recv(socks[0], &dummy, 1, 0); shutdown(socks[1], SHUT_WR); } ``` when racing like this: ``` thread1 thread2 unix_stream_read_generic mutex_lock(&u->iolock) skb_peek(&sk->sk_receive_queue) skb_peek_next(skb, &sk->sk_receive_queue) mutex_unlock(&u->iolock) unix_stream_read_generic unix_state_lock(sk) skb_peek(&sk->sk_receive_queue) unix_state_unlock(sk) unix_stream_data_wait unix_state_lock(sk) tail = skb_peek_tail(&sk->sk_receive_queue) spin_lock(&sk->sk_receive_queue.lock) __skb_unlink(skb, &sk->sk_receive_queue) spin_unlock(&sk->sk_receive_queue.lock) consume_skb(skb) [frees the SKB] `tail != last`: false `tail`: true `tail->len != last_len` ***UAF*** ``` Fix the UAF by removing the read of tail->len; checking tail->len would only make sense if SKBs in the receive queue of a UNIX socket could grow, which can no longer happen. Kuniyuki explained: > When commit 869e7c62486e ("net: af_unix: implement stream sendpage > support") added sendpage() support, data could be appended to the last > skb in the receiver's queue. > > That's why we needed to check if the length of the last skb was changed > while waiting for new data in unix_stream_data_wait(). > > However, commit a0dbf5f818f9 ("af_unix: Support MSG_SPLICE_PAGES") and > commit 57d44a354a43 ("unix: Convert unix_stream_sendpage() to use > MSG_SPLICE_PAGES") refactored sendmsg(), and now data is always added > to a new skb. That means this fix is not suitable for kernels before 6.5.

In the Linux kernel, the following vulnerability has been resolved: cifs: Fix busy dentry used after unmounting Since commit 340cea84f691c ("cifs: open files should not hold ref on superblock"), cifs file only holds the dentry ref_cnt, the cifs file close work(cfile->deferred) could be executed after unmounting, which will trigger a warning in generic_shutdown_super: BUG: Dentry 00000000a14a6845{i=c,n=file} still in use (1) [unmount of cifs cifs] The detailed processs is: process A process B kworker fd = open(PATH) vfs_open file->__f_path = *path // dentry->d_lockref.count = 1 cifs_open cifs_new_fileinfo cfile->dentry = dget(dentry) // dentry->d_lockref.count = 2 close(fd) __fput cifs_close queue_delayed_work(deferredclose_wq, cfile->deferred) dput(dentry) // dentry->d_lockref.count = 1 smb2_deferred_work_close _cifsFileInfo_put list_del(&cifs_file->flist) umount cleanup_mnt deactivate_super cifs_kill_sb cifs_close_all_deferred_files_sb cifs_close_all_deferred_files // cannot find cfile, skip _cifsFileInfo_put kill_anon_super generic_shutdown_super shrink_dcache_for_umount umount_check WARN ! // dentry->d_lockref.count = 1 cifsFileInfo_put_final dput(cifs_file->dentry) // dentry->d_lockref.count = 0 Fix it by flushing 'deferredclose_wq' before calling kill_anon_super. Fetch a reproducer in https://bugzilla.kernel.org/show_bug.cgi?id=221548.

In the Linux kernel, the following vulnerability has been resolved: virt: sev-guest: Explicitly leak pages in unknown state When set_memory_{encrypted,decrypted}() fail, the user cannot know at which point the function failed, meaning that the pages are left in an unknown state from the point of view of the caller. Since the pages may be left in an unencrypted state, they are not suitable for general use, and cannot be returned safely to the buddy allocator. Avoid the issue by never freeing the pages, and then do the proper accounting by calling snp_leak_pages().

In the Linux kernel, the following vulnerability has been resolved: scsi: isci: Fix use-after-free in device removal path The ISCI completion tasklet is initialized in isci_host_alloc() (drivers/scsi/isci/init.c:496) and scheduled from both MSI-X and legacy interrupt handlers (drivers/scsi/isci/host.c:223,613). isci_host_deinit() stops the controller and waits for stop completion, but it never kills completion_tasklet before teardown continues. A top-of-function tasklet_kill() is not sufficient here: interrupts are only disabled when isci_host_stop_complete() runs, so until wait_for_stop() returns the IRQ handlers can still requeue the tasklet. The tasklet callback also re-enables interrupts after draining completions, so killing the tasklet before the source is quiesced leaves the same race open. Once wait_for_stop() returns, no further IRQ-driven scheduling can occur. Kill completion_tasklet there so teardown cannot race a queued tasklet running on a dead ihost. On remove or unload, the stale callback can otherwise dereference ihost and touch ihost->smu_registers after the host lifetime ends. A UML + KASAN analogue reproduced the failure class both with no tasklet_kill() and with tasklet_kill() placed before source quiesce, and stayed clean once the kill happened after quiescing the scheduling source. This mirrors commit f6ab594672d4 ("scsi: aic94xx: fix use-after-free in device removal path"), but ISCI needs the kill after wait_for_stop().

In the Linux kernel, the following vulnerability has been resolved: drm/v3d: Fix use-after-free of CPU job query arrays on error path The CPU job ioctl's fail label calls kvfree() on cpu_job's timestamp and performance query arrays after v3d_job_cleanup(), which drops the job's last reference and frees cpu_job. Reading cpu_job at that point is a use-after-free. Also, on the early v3d_job_init() failure path, it is a NULL dereference, since v3d_job_deallocate() zeroes the local pointer. In the success path, the arrays are released from the scheduler's .free_job callback, but on the error path, they are freed manually, as the job was never pushed to the scheduler. While the success path deals with this correctly, the fail path doesn't. On top of that, the manual kvfree() calls only free the array storage; they don't drm_syncobj_put() the per-query syncobjs that v3d_timestamp_query_info_free() and v3d_performance_query_info_free() release on the success path. So the same fail path that triggers the use-after-free also leaks one syncobj reference per query. Unify the CPU job teardown into the CPU job's kref destructor, mirroring v3d_render_job_free(). The scheduler's .free_job slot reverts to the generic v3d_sched_job_free() and the fail label drops the manual kvfree() calls, leaving a single teardown path that is reached from both the scheduler and the ioctl error path. That removes the use-after-free, the NULL dereference, and the syncobj leak by construction.

In the Linux kernel, the following vulnerability has been resolved: drm/virtio: use uninterruptible resv lock for plane updates virtio_gpu_cursor_plane_update() and virtio_gpu_resource_flush() lock the framebuffer BO's dma_resv via virtio_gpu_array_lock_resv() and ignore its return value. The function can fail with -EINTR from dma_resv_lock_interruptible() (signal during lock wait) or with -ENOMEM from dma_resv_reserve_fences() (fence slot allocation), leaving the resv lock not held. The queue path then walks the object array and calls dma_resv_add_fence(), which requires the lock held; with lockdep enabled this trips dma_resv_assert_held(): WARNING: drivers/dma-buf/dma-resv.c:296 at dma_resv_add_fence+0x71e/0x840 Call Trace: virtio_gpu_array_add_fence virtio_gpu_queue_ctrl_sgs virtio_gpu_queue_fenced_ctrl_buffer virtio_gpu_cursor_plane_update drm_atomic_helper_commit_planes drm_atomic_helper_commit_tail commit_tail drm_atomic_helper_commit drm_atomic_commit drm_atomic_helper_update_plane __setplane_atomic drm_mode_cursor_universal drm_mode_cursor_common drm_mode_cursor_ioctl drm_ioctl __x64_sys_ioctl Beyond the WARN, mutating the dma_resv fence list without the lock races with concurrent readers/writers and can corrupt the list. Both call sites run inside the .atomic_update plane callback, which DRM atomic helpers do not allow to fail (by the time it runs, the commit has been signed off to userspace and there is no clean rollback path). Moving the lock acquisition to .prepare_fb was rejected because the broader lock scope deadlocks against other BO locking paths in the same atomic commit. Introduce virtio_gpu_lock_one_resv_uninterruptible() that uses dma_resv_lock() instead of dma_resv_lock_interruptible(). This eliminates the -EINTR failure mode -- the realistic syzbot trigger -- without extending the lock hold across the commit. The helper locks a single BO and rejects nents > 1 with -EINVAL; both fix sites lock exactly one BO. Use it from virtio_gpu_cursor_plane_update() and virtio_gpu_resource_flush(); check the return value to handle the remaining -ENOMEM case from dma_resv_reserve_fences() by freeing the objs and skipping the plane update for that frame. The framebuffer BOs touched here are not shared with other contexts and lock contention is expected to be brief, so the loss of signal-interruptibility is acceptable. Other callers of virtio_gpu_array_lock_resv() (the ioctl paths) continue to use the interruptible variant. The bug was reported by syzbot, triggered via fault injection (fail_nth) on the DRM_IOCTL_MODE_CURSOR path, which forces the -ENOMEM branch in dma_resv_reserve_fences().

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Validate GPIO pin LUT table size before iterating [Why&How] The GPIO pin table parsers in get_gpio_i2c_info() and bios_parser_get_gpio_pin_info() derive an element count from the VBIOS table_header.structuresize field, then iterate over gpio_pin[] entries. However, GET_IMAGE() only validates that the table header itself fits within the BIOS image. If the VBIOS reports a structuresize larger than the actual mapped data, the loop reads past the end of the BIOS image, causing an out-of-bounds read. Fix this by calling bios_get_image() to validate that the full claimed structuresize is accessible within the BIOS image before entering the loop in both functions. (cherry picked from commit ba5e95b43b773ae1bf1f66ee6b31eb774e65afe3)

In the Linux kernel, the following vulnerability has been resolved: batman-adv: mcast: fix use-after-free in orig_node RCU release batadv_mcast_purge_orig() removes entries from RCU-protected hlists but does not wait for an RCU grace period before returning. Concurrent RCU readers may still accesses references to those entries at the point of removal. RCU-protected readers trying to operate on entries like orig->mcast_want_all_ipv6_node will then access already freed memory. Fix this by moving batadv_mcast_purge_orig() to batadv_orig_node_release(), just before the call_rcu() invocation. This ensures RCU readers that were active at purge time have drained before the orig_node memory is reclaimed.

In the Linux kernel, the following vulnerability has been resolved: batman-adv: bla: avoid double decrement of bla.num_requests The bla.num_requests is increased when no request_sent was in progress. And it is decremented in various places (announcement was received, backbone is purged, periodic work). But the check if the request_sent is actually set to a specific state and the atomic_dec/_inc are not safe because they are not atomic (TOCTOU) and multiple such code portions can run concurrently. At the same time, it is necessary to modify request_sent (state) and bla.num_requests atomically. Otherwise batadv_bla_send_request() might set request_sent to 1 and is interrupted. batadv_handle_announce() can then set request_sent back to 0 and decrement num_requests before batadv_bla_send_request() incremented it. The two operations must therefore be locked. And since state (request_sent) and wait_periods are only accessed inside this lock, they can be converted to simpler datatypes. And to avoid that the bla.num_requests is touched by a parallel running context with a valid backbone_gw reference after batadv_bla_purge_backbone_gw() ran, a third state "stopped" is required to correctly signal that a backbone_gw is in the state of being cleaned up.

In the Linux kernel, the following vulnerability has been resolved: batman-adv: tp_meter: directly shut down timer on cleanup batadv_tp_sender_cleanup() was calling timer_delete_sync() followed by timer_delete() to guard against the timer handler re-arming itself between the two calls. This double-deletion hack relied on the sending status being set to 0 to suppress re-arming. Replace both calls with a single timer_shutdown_sync(). This function both waits for any running timer callback to complete (like timer_delete_sync()) and permanently disarms the timer so it cannot be re-armed afterwards, making re-arming prevention unconditional and self-documenting. The re-arming property is also required because otherwise: 1. context 0 (batadv_tp_recv_ack()) checks in batadv_tp_reset_sender_timer() if sending is still 1 -> it is 2. context 1 changes in batadv_tp_sender_shutdown() sending to 0 and in this process forces the kthread to stop timer in batadv_tp_sender_cleanup() 3. context 0 continues in batadv_tp_reset_sender_timer() and rearms the timer -> but the reference for it is already gone

In the Linux kernel, the following vulnerability has been resolved: batman-adv: tt: fix negative tt_buff_len batadv_orig_node::tt_buff_len was declared as s16, but the field is never intended to hold a negative value. When a value greater than 32767 is assigned, it wraps to a negative signed integer. In batadv_send_other_tt_response(), tt_buff_len is temporarily widened to s32. The incorrectly negative s16 value propagates into the s32, causing batadv_tt_prepare_tvlv_global_data() to allocate a full sized buffer but populates only a small portion of it with the collected changeset. All remaining bits are kept uninitialized. Using an u16 avoids this type confusion and ensures that no (negative) sign extension is performed in batadv_send_other_tt_response().

In the Linux kernel, the following vulnerability has been resolved: hwmon: (pmbus/adm1266) include PEC byte in pmbus_block_xfer read buffer adm1266_pmbus_block_xfer() sets up the read transaction with .buf = data->read_buf, .len = ADM1266_PMBUS_BLOCK_MAX + 2, but read_buf in struct adm1266_data is declared as u8 read_buf[ADM1266_PMBUS_BLOCK_MAX + 1]; For a max-length block response (length byte = 255 + up to 1 PEC byte), the i2c controller is told to write 257 bytes into a 256-byte buffer, putting one byte past the end of read_buf. The same response also makes the subsequent PEC compare if (crc != msgs[1].buf[msgs[1].buf[0] + 1]) read a byte beyond the array. Bump the read_buf declaration to ADM1266_PMBUS_BLOCK_MAX + 2 so the buffer can hold the length byte, up to 255 payload bytes, and the PEC byte the i2c_msg length already accounts for.